Characteristics:
-Small enough to fit on an office desk. As such, the machine can be used in the corner of a lab to conduct the same level of testing as an actual machine.
-Universal rack type coating unit. Because the coating unit can be easily exchanged, the system allows for different coating methods to be used, including roll, die, knife, gravure, and other methods.
-High-precision aluminum profile system frame. This frame system allows for various drying systems and instrumentation to be attached, while the width and size of future machine sizes can be easily altered.

Specifications:
-We design and develop systems for various applications
-Contact us for specifications

“Thin”
A fine wire bar realizes ultra-thin coatings of 1.5 g/m² (wet)

“Easy”
A semi-closed system reduces volatilization of solvents
Reduces coating fluid circulation volume

“Compact”
Easy to modify or expand existing facilities
Metering and fluid supply are integrated

Specifications:
Coating Width: 2,600 mm (max.)
Speed: 10 to 200 m/min
Substrates: film, paper, etc.
Coating Weight: 1.5 to 17.0 g/m² (wet)
Viscosity: under 150 mPa•s
Coatings: water-based/organic solvent types

Since its inception in 1963, our coaters have been installed in many locations throughout the world in the paper and film industries, contributing to the development of new products and improvement of existing products.
The following introduces our ultra-thin-film coater.

Specifications:
-Substrates: 6 to 188 μm PET
-Speed: 800 m/min
-Coating Method: reverse roll coater, direct gravure coater

Characteristics:
-Allows for easy control of coating weight by simply changing out the wire bar with that having a different wire thickness.
-The wire bar is driven by a motor. Uniform coating samples can be produced at the design speed.
-The pressing force of the bar can be adjusted using an attached weight.
-The table uses a glass plate with excellent surface roughness, so is easy to clean.

Specifications:
Substrate Size: B4 size (max.)
Table Material: anodized aluminum + glass plate
Power Supply: AC 100V, 60W, 50/60Hz phase
Bar Travel: motor drive, 5 to 250 mm/sec
Bar Pressing Method: weight type (1.9/2.6/3.2 kgf over entire width)
Frame Weight: frame 28 kg, operational panel 6 kg

Test Bar Specifications:
Rod Diameter: 10 mm (standard), can handle 8 to 12 mm
Wire Diameter: can handle diameters from 20 μm
Material: SUS304

Through a technological exchange with a non-Japanese manufacturer in 1970, we developed this slitter/rewinder as a shift in thinking away from European concepts to Japanese needs under the strict quality management system of Japanese users. Our slitter/rewinders have been installed in many locations around the world.
The following introduces the FUS Slitter.

Specifications:
-Substrates: PET, OPP, etc.
-Substrate Thickness: 1 to 350 μm
-Substrate Width: 2,000 to 8,400 mm
-Speed: 800 m/min

Through a technological exchange with a non-Japanese manufacturer in 1970, we developed this slitter/rewinder as a shift in thinking away from European concepts to Japanese needs under the strict quality management system of Japanese users. Our slitter/rewinders have been installed in many locations around the world.
The following introduces the PRS-1500 Rewinder.

Specifications:
-Substrates: high-quality paper, thermo-sensitive paper
-Substrate Weight: 40 to 170 g/m²
-Unwinding Diameter: 1,800 mm (max.)
-Rewinding Diameter: 1,200 mm (max.)
-Speed: 1,500 m/min

Characteristics:
The knife unit uses a die-set configuration, which allows the blade shape to be changed to handle the desired cutting pattern (including punching). Although the upper cutter moves vertically against the lower cutter, the lower cutter slides horizontally in synchronization with the traveling sheet to be cut, allowing for travel cutting to be synchronized to the line speed. As such, the line speed is constant, while factors that cause sheet slip damage and cutting precision variation that may result during acceleration and deceleration during intermittent operation are eliminated. The series of knife unit cutting actions is driven by a simple drive system using one drive shaft, so the design applies an extremely low amount of load power for a die-set type cutting machine. As such, it allows for high-speed, high-precision cutting.

Low-cost!!
We modify and repair various converting related systems with short delivery times.
Feel free to contact us.

Characteristics:
By combining our many years of experience with T-dies and precision processing technology, we have developed this ultra-precision coating die.
Die Straightness: less than 0.002 mm at L1,000 mm
less than 0.005 mm at L2,000 mm
Die Surface Roughness: Rmax less than 0.2

Specifications:
Material: SUS
Coating Thickness: thin to thick films
Die Width: 300 to 2,200 mm
Other specifications can be made to meet customer requests.

Options:
Special arbitrary lip positioning control mechanism die (patented)